Poka? wyniki od 1 do 1 z 1

Temat: g35 Jak czytać kody / reset kodów / opis poszczególnych kodów

  1. #1
    Forumowy wyjadacz Avatar solista
    Do??czy?
    Mar 2011
    Mieszka w
    Szczecin
    Jeździ
    ^ g35 coupe
    Postów
    276
    Podziękował
    1
    Otrzymał podziękowanie 5 raz/y

    Domy?lnie g35 Jak czytać kody / reset kodów / opis poszczególnych kodów

    Jak gdzieś ten temat jest to wywalcie - bo ja nie znalazłem

    CZYTANIE KODÓW BŁĘDÓW SES:

    W sytuacji gdy zapala się nam Service Engine Soon (SES) należy sprawdzić jaki błąd nam wyskoczył. Robimy to w następujący sposób:
    Confirm that accelerator pedal is fully released, turn ignition switch “ON” and wait 3 seconds.
    Repeat the following two procedures quickly five times within 5 seconds:
    Fully depress the accelerator pedal (HARD).
    Fully release the accelerator pedal.
    Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.
    Fully release the accelerator pedal (while the CEL is still blinking)

    I w tym momencie możemy odczytać kody błędów, robimy to w następujący sposób:
    Długie mignięcia oznaczają pierwszą cyfrę: 10 mignięć oznacza 0 (dzięki temu że są długie mignięcia wiemy że pokazuje nam pierwszą cyfrę). Następnie liczymy pozostałe mignięcia (już krótkie), gdzie każda grupa oznacza kolejną cyfrę w kodzie.
    Np: 10 długich, 3 krótkie, 4 krótkie, 5 krótkich to kod P0345.
    Jeżeli jest wiecej niż jeden błąd to będą one wyświetlane po sobie.

    RESETOWANIE KODÓW BŁĘDÓW (CZYSZCZENIE)

    Jak już dowiemy się jakie błędy nam poleciały (nadal jesteśmy w trybie serwisowym zgodnie z opisem powyżej - czyli SES wciąż wyświetla kody błędó) wystarczy wcisnąć pedał gazu na ponad 10 sek i później go puścić. Następnie przekręcamy stacyjkę na OFF. Przy kolejnym odpaleniu błędów już nie powinno być.

    Pełna procedura kasowania błędów:
    Confirm that accelerator pedal is fully released, turn ignition switch “ON” and wait 3 seconds.
    Repeat the following two procedures quickly five times within 5 seconds:
    Fully depress the accelerator pedal (HARD).
    Fully release the accelerator pedal.
    Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.
    Fully release the accelerator pedal (while the CEL is still blinking)
    Wait about 10 seconds.
    Fully depress the accelerator pedal and keep it for more than 10 seconds.
    Fully release the accelerator pedal (The CEL light will continue to blink).
    Turn ignition switch to “OFF” position and now you can start the car. The CEL light should be gone

    LISTA KODÓW I CO OZNACZAJĄ

    - Codes
    P0000 No Self Diagnostic Failure Indicated
    P0011 Intake Valve Timing Control
    P0021 Intake Valve Timing Control
    P0031 O2 Sensor Heather
    P0032 O2 Sensor Heather
    P0037 O2 Sensor Heather
    P0038 O2 Sensor Heather
    P0043 O2 Sensor Heather
    P0044 O2 Sensor Heather
    P0051 O2 Sensor Heather
    P0052 O2 Sensor Heather
    P0057 O2 Sensor Heather
    P0058 O2 Sensor Heather
    P0100 MAF (Mass Air Flow) Sensor
    P0101 MAF Sensor
    P0102 MAF Sensor
    P0103 MAF Sensor
    P0105 Absolute Pressure Sensor
    P0107 Absolute Pressure Sensor
    P0108 Absolute Pressure Sensor
    P0110 IAT (Intake Air Temperature) Sensor
    P0112 IAT Sensor
    P0113 IAT Sensor
    P0115 ECT (Engine Coolant Temperature) Sensor
    P0117 ECT Sensor
    P0118 ECT Sensor
    P0120 TP (Throttle Position) Sensor
    P0121 TP Sensor
    P0122 TP Sensor
    P0123 TP Sensor
    P0125 ECT Sensor
    P0127 Intake Air Temperature Sensor
    P0128 Thermostat Function
    P0130 Closed Loop, Bank 1 Or Front O2S, Bank 1
    P0131 Front O2 Sensor, Bank 1 Lean Shift Monitoring
    P0132 Front O2 Sensor, Bank 1 Rich Shift Monitoring
    P0133 Front O2 Sensor, Bank 1 Response Monitoring
    P0134 Front O2 Sensor, Bank 1 High Voltage
    P0135 Front HO2S Heater, Bank 1
    P0136 Rear O2S, Bank 1
    P0137 Rear O2S, Bank 1 Minimum Voltage Monitoring
    P0138 Rear O2S, Bank 1 Maximum Voltage Monitoring
    P0139 Rear O2S, Bank 1 Response Monitoring
    P0140 Rear O2S, Bank 1 High Voltage
    P0141 Rear H02S Heater, Bank 1
    P0144 O2 Sensor Heather
    P0150 Closed Loop, Bank 2 Or Front O2S, Bank 2
    P0151 Front O2 Sensor, Bank 2 Lean Shift Monitoring
    P0152 Front O2 Sensor, Bank 2 Rich Shift Monitoring
    P0153 Front O2 Sensor, Bank 2 Response Monitoring
    P0154 Front O2 Sensor, Bank 2 High Voltage
    P0155 Front HO2S Heater, Bank 2
    P0156 Rear H02S Sensor, LH Bank
    P0157 Rear O2S, Bank 2
    P0158 Rear O2S, Bank 2
    P0159 Rear O2S, Bank 2
    P0160 Rear O2S, Bank 2
    P0161 Rear H02S Heater, LH Bank Or Bank 2
    P0171 Fuel System Lean, Bank 1
    P0172 Fuel System Rich, Bank 1
    P0174 Fuel System Lean, Bank 2
    P0175 Fuel System Rich, Bank 2
    P0180 Tank Fuel Temp Sensor
    P0182 Fuel Tank Temperature Sensor
    P0183 Fuel Tank Temperature Sensor
    P0217 Engine Coolant High Temperature Enrichment Protection
    P0221 Throttle Position Sensor
    P0222 Throttle Position Sensor
    P0223 Throttle Position Sensor
    P0226 Accelerator Pedal Position Sensor
    P0227 Accelerator Pedal Position Sensor
    P0228 Accelerator Pedal Position Sensor
    P0245 Supercharger Bypass Valve Control Solenoid Valve
    P0300 Random Misfire
    P0301–*P0308 Misfire, Cylinder No. 1–8
    P0325 Knock Sensor, Bank 1
    P0327 Knock Sensor
    P0328 Knock Sensor
    P0330 Knock Sensor, Bank 2
    P0335 CKP (Crank Shaft Position) Sensor
    P0340 CMP (Cam Shaft Position) Sensor (Phase)
    P0345 CMP Sensor (Phase)
    P0350 Ignition Signal
    P0400 EGR System
    P0402 EGRC/BPT Valve
    P0403 EGR Volume Control Valve Circuit
    P0405 EGR Temperature Sensor
    P0406 EGR Temperature Sensor
    P0420 TW (Two-Way) Catalyst System, Bank 1
    P0430 TW Catalyst System, Bank 2
    P0440 EVAP Small Leak
    P0441 EVAP Control System Purge Flow Monitor
    P0442 EVAP Control System
    P0443 Purge Control/V & S/V
    P0444 EVAP Canister Purge Volume Control Solenoid Valve
    P0445 EVAP Canister Purge Volume Control Solenoid Valve
    P0447 EVAP Canister Vent Control Valve
    P0450 EVAP Pressure Sensor
    P0451 EVAP System Pressure Sensor
    P0452 EVAP System Pressure Sensor
    P0453 EVAP System Pressure Sensor
    P0455 EVAP Control System
    P0456 EVAP Control System
    P0460 Fuel Level Sensor Unit (Slow)
    P0461 Fuel Level Sensor Function
    P0462 Fuel Level Sensor
    P0463 Fuel Level Sensor
    P0464 Fuel Level Sensor Circuit
    P0500 Vehicle Speed Sensor
    P0505 IACV/AAC Valve
    P0506 Idle Speed Control System
    P0507 Idle Speed Control System
    P0510 Closed TP Sensor
    P0550 Power Steering Pressure Sensor
    P0600 A/T Comm Line
    P0605 ECM/ECU
    P0650 Malfunction Indicator Lamp
    P0705 PNP Or Inhibitor Switch
    P0710 ATF Temp Sensor
    P0720 VSS A/T
    P0725 Engine Speed Signal
    P0731 A/T 1ST Signal
    P0732 A/T 2ND Signal
    P0733 A/T 3RD Signal
    P0734 A/T 4TH Signal Or TCC
    P0740 TCC SV Solenoid
    P0744 A/T TCC Signal
    P0745 Line Pressure S/V
    P0750 Shift Solenoid/V A
    P0755 Shift Solenoid/V B

    Trochę te opisy się różnią z moim Hayness-em, ale w miarę gra
    S.

  2. Dzięki solista za powyższy Post:

    Tomek g35c (6th-February-2016)

Podobne w?tki

  1. Lusterko z pamięcią kodów do bramy problem
    By marko in forum Audio, Nawigacja & Elektornika
    Odpowiedzi: 8
    Ostatni post / autor: 11th-April-2017, 02:17
  2. Reset silniczka opuszczania szyby - jak to zrobić...
    By sirtrojan in forum Wewnętrzna Modyfikacja
    Odpowiedzi: 0
    Ostatni post / autor: 9th-June-2012, 19:22
  3. Dane techniczne FX 35 i opis generacji
    By JarekT in forum Generalne Informacje i Pytania
    Odpowiedzi: 1
    Ostatni post / autor: 27th-September-2011, 19:24
  4. Kody błędów - INFINTI FX35 FX45 / G35
    By sirtrojan in forum Infiniti - dyskusje i wątki ogólne
    Odpowiedzi: 0
    Ostatni post / autor: 16th-May-2010, 00:37
  5. INFINITI G35/37 Kody Lakierów
    By Jacob_USA in forum Generalne Informacje i Pytania
    Odpowiedzi: 0
    Ostatni post / autor: 30th-January-2010, 07:35

Uprawnienia

  • Nie mo?esz zak?ada? nowych tematów
  • Nie mo?esz pisa? wiadomo?ci
  • Nie mo?esz dodawa? za??czników
  • Nie mo?esz edytowa? swoich postów
  •